CAE PERFORMANCE PRODUCTS
E.F.I. Wiring Kits - Holden V8 or V6
E.F.I. wiring kits for Gemini - TC-TD-TE-TF-TX fitted with Holden V6 - Manual or Auto Transmission.

For information click here

CAE PERFORMANCE PRODUCTS LOOMEFI-01  Engine Management loom to suit Holden Series 1 and 2 V6 Commodore Engines    $660 c/o  
CAE PERFORMANCE PRODUCTS LOOMEFI-08  Engine Management loom to suit Commodore V6 Ecotec Engines with Auto or Manual Conversion loom. Suit under dash set-up.    $880c/o  
CAE PERFORMANCE PRODUCTS MEMCAL-VT/V8  Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) and Calibrated to suit conversion.    $450c/o  
CAE PERFORMANCE PRODUCTS MEMCAL-VT/V6  Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) and Calibrated to suit conversion.    $450c/o  
ERROR: MEMCAL-VR/V6 Man  MEMCAL-VR/V6 MAN  
CAE PERFORMANCE PRODUCTS MEMCAL-VR/V6 AUTO  Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) and Calibrated to suit conversion.    $450c/o  
CAE PERFORMANCE PRODUCTS LOOMS/S-01  Speed Sensor assembly and Loom with speedo cable provision. Suit T-700 Auto Trans.    $300  
CAE PERFORMANCE PRODUCTS LOOMS/S-02  Speed Sensor assembly and Loom with speedo cable provision. Suit T-350-400. Powerglide Auto Trans.     $240  
CAE PERFORMANCE PRODUCTS B0580464070  Hi-pressure EFI fuel pump    $195  
CAE PERFORMANCE PRODUCTS BF-5030  Hi-pressure fuel filter    $20  
CAE PERFORMANCE PRODUCTS 11004/KIT  Lift pump. Low pressure    $140  
CAE PERFORMANCE PRODUCTS ST-4  EFI Surge Tank Round 130x250cm    $180  
CAE PERFORMANCE PRODUCTS FAN-EF4026  16in. 2100cfm UNIVERSAL FAN    $180  
CAE PERFORMANCE PRODUCTS SUMP-04B  V6 Commodore VN-VP-VR engine into early Holdens Toranas and Gemini. Need original Sump and Oil Pickup as change over unit.    $550  
CAE PERFORMANCE PRODUCTS SUMP-04A  V6 Commodore Ecotec engine suit Early Holdens Toranas and Gemini. Need Oil Pickup as change over unit    $660  
CAE PERFORMANCE PRODUCTS CH-EM64  HOLDEN GEMINI with COMMODORE V6 (Includes rubbers)    $353  
CAE PERFORMANCE PRODUCTS A1158  Transmission rubber mount to suit T700 and T5    $44  
CASTLE HEADERS CH-74  HOLDEN GEMINI WITH V6 3.8 EFI COMMODORE ENGINE 3 INTO 1 DESIGN. 1 5/8in. (must use engine mounts EM-64 and original Bosch Starter - May not fit with CRS Sump)    $770  
CASTLE HEADERS CH-76  HOLDEN TORANA LH-LX-UC and HQ-WB WITH V6 3.8 EFI COMMODORE ENGINE. 3 INTO 1 DESIGN. 1 5/8in. INCLUDES Y-PIECE (must use engine mounts CH-EM60)    $600  
HI-TORQUE G/R-03/V6A1.9  V6 3.8ltr Commodore Engine. Suit Automatic trans. (9 Tooth pinion)    $350  
HI-TORQUE G/R-03/V6M1.9  V6 3.8ltr Commodore Engine. Suit Manual trans. (10 Tooth pinion)    $350  
CAE PERFORMANCE PRODUCTS V6-IDLER  Commodore Ecotec V6 engine Idler Pulley includes drive belt    $220  
Customer Information

Details for Customer

For a V6 application, the engine mounts are used in conjunction with original red motor 6cyl rubbers.

The engine bay harness is connected to original loom under D/side dash and control loom is mounted on D/side inner fender.

The E.C.M. is mounted on the LHS kick panel or above the glove box.

Our loom is sold on a changeover basis for the engine to computer loom.
If no changeover loom is supplied, an additional cost of $200.00 will apply.

Prices may vary slightly if an Ecotech engine is used.

All Prices in $Au including GST. Overseas orders will be lower. 
Back to the EFI wiring page